Yonex Exbolt 65: String Guide & Stringing in Setapak KL
Yonex Exbolt 65 is a 0.65 mm badminton string with a Forged Fiber outer and Elasticity Outer coating. Compare quick response and soft-shot placement before restringing in Setapak.

Exbolt 65 is its own construction
The official code is BGXB65. Yonex specifies a high-intensity nylon multifilament core, a special braided Forged Fiber outer and an Elasticity Outer coating. The nominal diameter is 0.65 mm, and the product specification lists Japan as its origin. The number identifies this particular model; it is not a suggested tension.
Exbolt 65 shares part of its family name with Exbolt 63 and Exbolt 68, but those are separate products. The 63 has a different diameter and does not list this coating in its global specification. The 68 uses a thicker, oval Forged Fiber outer construction. Confirm the code on the actual packet when discussing a change, rather than asking for any Exbolt string.
Look for BGXB65 on the 10 metre packet. If your stringing receipt says only Exbolt, check which diameter you used before you book again. The 63 and 68 each use their own specification and are useful alternatives when changing gauge is part of the trial.

Explore pace at both ends of the rally
Yonex positions Exbolt 65 around quick response and shuttle hold. For your own comparison, those are two questions: can you reach your usual clear length with a relaxed action, and can you reduce pace for a short block? A setup that feels lively in drives may still require a touch adjustment near the net.
Try familiar feeds and alternate between a full-length shot and a soft return. Notice the depth you produce and whether you need to grip harder than usual. This is conditional trial advice, not a report of an ERR controlled test. The useful choice is the response you can repeat, rather than the fastest-sounding description on the packet.
The impact note is another part of the experience. A high or crisp sound may appeal to you, but it does not measure shuttle speed or control. Keep sound preference separate from whether the next shot actually lands where you intended.
Try a simple pair of strokes from the same midcourt feed. Drive the shuttle to a familiar lane, then take pace off and send it shallower. If you can repeat both landing points without changing grip more than usual, you have a practical observation about the setup to discuss.

What the coating does and does not establish
The official launch explanation describes Elasticity Outer as a flexible nylon coating using NANOALLOY technology, with increased shuttle hold as a brand claim. This gives a construction difference to discuss with Exbolt 63. It does not provide a universal dwell-time measurement or prove that every player will feel more control.
Do not translate the word elasticity into a guarantee that the completed racket feels soft. Frame design, installation and contact conditions also matter. Likewise, the specification does not give a measured surface-friction value. If surface sensation is important to you, describe your blocks and net shots instead of assuming the coating must feel rougher or grippier.
The educational images explain how to compare a setup. They are not microscope photographs of the coating, nor diagrams of a verified molecular structure. Exact materials and dimensions remain in the written specification and comparison table.

Choose a baseline your racket supports
Start with the full racket model, weight version, frame condition and previous stringing request. The applicable racket instructions and permitted range remain the limits for an Exbolt 65 installation. A durability claim does not override a damaged grommet, a compromised frame or the manufacturer's pattern.
There is no single Exbolt 65 tension for all KL players. If you are changing from Ultimax at the same nominal diameter, the different construction is still a variable. Decide whether to keep a familiar baseline for comparison or adjust it because the old setup already felt too demanding; discuss that reason before installation.
Pre-stretch, main-and-cross differences and knot locations belong to the specific racket and machine procedure. Do not copy a percentage from another person's setup automatically. Record what was requested so your next discussion is based on something more useful than a remembered impact sound.
Make a note of the previous string and requested pounds before switching to Exbolt 65. Ask your stringer which setting still fits the frame and its condition. Keeping a familiar grip and shuttle type makes it easier to describe what you noticed on the string change.

Keep durability separate from response retention
A string can remain unbroken while its response changes. Conversely, an off-centre break can end a trial before gradual wear becomes the main issue. For Exbolt 65, record both playing exposure and the shots that begin to feel different. A calendar date alone cannot explain how much use the string has received.
Check wear at the intersections and note repeated breaks near the same frame hole. The latter deserves a grommet and frame inspection before blaming the coating or choosing a thicker replacement. Forged Fiber is not protection against every cause of failure.
No verified ERR Exbolt 65 DT series is available in the material checked for this page. The measurement section therefore explains what to record without drawing an invented loss curve. Neither a manufacturer durability score nor another string's historical reading establishes Exbolt 65 retention in your racket.
When you first notice a change in response, record how many hours you played and which part of the bed shows wear. Compare those notes with the easy clear and soft return you already tested. A different Exbolt diameter can be a useful follow-up when upkeep becomes the main issue.

Compare the trade-off that matters to you
Exbolt 65 is worth considering when you want to compare a thin response-oriented string while paying particular attention to pace on touch shots. This is a preference to investigate, not a promise that it suits every attacking player. Include defensive blocks as well as drives when judging whether the response is useful.
Exbolt 63 offers a thinner family comparison; Exbolt 68 offers a thicker construction with a stronger durability emphasis. BG66 Ultimax is useful when you want to hold nominal gauge at 0.65 mm while comparing a different outer construction. None of these alternatives is an automatic upgrade, and brand profile values are not a controlled cross-brand ranking.
If your biggest concern is the cost of repeated replacement, say so before choosing. If your current racket already feels harsh or tiring, a new coating name alone is not a solution. A sensible result may be a different model, a more appropriate installation, or equipment maintenance before another string trial.
Exbolt 65 Knowledge Check
How well do you know this string?
0 / 8 answeredYour result
Review each answer, then try again when you are ready.
| Nominal gauge | 0.65 mm |
|---|---|
| Product code | BGXB65 |
| Retail set length | 10 m |
| ERR restring | RM51.00, string and labour |
See the response profile
Five-characteristic spider chart
Contact, deflection and rebound
Press play to follow contact → deflection → rebound.
Slow-motion teaching diagram, not a measured speed or tension test.
The numbers behind the feel
Yonex's 2026 catalogue rates Exbolt 65 across five characteristics. These are brand-relative values, not ERR measurements, percentages or a cross-brand ranking. The chart uses an 11-point display because the catalogue includes scores above 10.
Exbolt 65 DT and response tracking
No verified ERR Exbolt 65 time series is available in the checked material. A curve would imply measurements we do not have. Use the following record when discussing changes in your setup.
Record the installation
Racket model, string code, requested tension, date and applicable machine procedure.
Use a consistent method
Record instrument, units, measurement method and timing. DT, machine pounds and phone frequency are different quantities.
Track actual exposure
Note elapsed time, playing hours and storage conditions. Calendar days alone do not describe use.
Connect readings to play
Record clear length, soft returns and wear. A reading alone does not decide when every player must restring.
Exbolt 65 and three alternatives
Compare construction and priorities rather than treating a model name as an upgrade ladder. These are different options, not a controlled ranking.
| String | Gauge | Construction or feel | What to check on court |
|---|---|---|---|
| Exbolt 65 | 0.65 mm | Forged Fiber outer; Elasticity Outer coating | Check pace on soft returns as well as clears |
| Exbolt 63 | 0.63 mm | Forged Fiber outer; no Elasticity Outer listed | Do you prefer the response enough to accept maintenance? |
| Exbolt 68 | 0.68 mm | Oval Forged Fiber; Elasticity Outer coating | Consider wear alongside your preferred contact |
| BG66 Ultimax | 0.65 mm | Nylon multifilament core; braided nylon outer | Same diameter does not establish the same feel |
Exbolt 65 and Ultimax share a nominal gauge but have different outer constructions. The 63 and 68 provide separate family comparisons; none is a universal upgrade.
What would you like to feel differently?
For Exbolt 65, distinguish a touch preference from an equipment or maintenance issue. A coating claim does not explain every short clear, fast block or repeated break.
Track the change, not just the sound
Some settling after stringing is normal. Record when the racket starts to feel different, the hours played and storage conditions. Compare readings using the same method; a phone frequency reading is not the machine setting in pounds. Ask about installation consistency before assuming a different packet will solve it.
Bring this question to ERR →Separate contact from setup
A stiff-feeling bed, late contact, shuttle speed and technique can all make length difficult. Start with relaxed clears and describe where the shuttle lands. Review your current tension within the racket limit rather than increasing it automatically.
Bring this question to ERR →The break location matters
A break near the same grommet deserves a frame and grommet check. Breakage after off-centre contact differs from gradual notching in the centre. Bring the racket and a photo of the break; do not assume every early break means the string is defective.
Bring this question to ERR →Describe what your hand notices
Tell the stringer which shots feel unforgiving and when the sensation began. Compare contact consistency, string choice and tension. Stringing advice is not a treatment for persistent pain; stop playing through pain and seek appropriate assessment.
Bring this question to ERR →Inspect before installation
Photograph existing chips and discuss cracks, worn grommets and frame shape before work begins. Correct support, the appropriate pattern and staying within the racket limit matter. A chipped finish alone does not establish who caused damage.
Bring this question to ERR →Explain the change clearly
Grip size, balance, racket weight, stringbed response and timing are different things. A restring does not turn a head-heavy racket into a head-light one. Tell the stringer what changed and compare with your previous setup instead of asking only for more power.
Bring this question to ERR →What matters on court?
Choose what you want from your next restring.
Repeat a drive and a shallow return
Use one predictable feed for both. Check whether the response feels useful across two speeds with the usual grip.
Ask your stringerCan Exbolt 65 keep my drive response and give me quiet blocks?
Compare upkeep within the Exbolt family
Record playing time and inspect edge breaks separately from centre wear. Try Exbolt 68 when gauge is a deliberate part of the comparison.
Ask your stringerIs the 68 worth testing for my break and wear pattern?
Start with a familiar clear
Note the effort required for an ordinary clear before asking to change the setting. Discuss the actual frame and its limits.
Ask your stringerWhat familiar setting would make a fair Exbolt 65 trial?
Check placement against Ultimax
Compare two 0.65 mm models with different outer designs. Use the same racket and try a short net reply at reduced pace.
Ask your stringerWhich two returns make the comparison most useful for me?
Different equipment. Different questions.
Different rackets
The same requested pounds can feel different across frame shapes and stringbed dimensions. Record the racket, not just the number.
Try Exbolt 65 on the same racket first. Record the full racket model and the agreed tension before trying another frame.
Different strings
Gauge, construction and surface feel change the comparison. Do not treat every thin string as the same product.
Compare Exbolt 65 with Exbolt 63 using the same racket and familiar shots. Use the table above to check gauge and construction before changing the setup.
Different installation
Machine calibration, support, clamps, pattern and technique can affect consistency. Ask about the process as well as qualifications.
If Exbolt 65 repeatedly breaks near the same hole, show your stringer a close-up of that spot and ask them to inspect the grommet.
Different sessions
Shuttle speed, hall conditions, fatigue and timing influence feedback. Compare familiar drills before drawing a conclusion.
Use the same shuttle speed and repeat a few clears, drives and net shots. Record playing hours alongside any change in how Exbolt 65 feels.
Prepare, play and review with purpose.
Bring your racket history
Note your racket model, previous string, requested tension and the change you want. A photo of recurring breakage helps.
Make the plan specific
Review the frame and grommets. Confirm string, colour availability, tension within the racket limit and price before work starts.
Keep a useful record
Keep the string model, requested tension and date together. Ask about the pattern and checks relevant to your racket.
Repeat familiar shots
Try clears, drives, blocks and net shots under comparable conditions. Record comfort, length and placement, not only sound.
Change one thing at a time
Bring your observations back. Keep the setup if it works; otherwise agree on one practical change for the next restring.
Exbolt 65 questions, clearly answered.
What is the exact Exbolt 65 code and gauge?
The code is BGXB65 and the nominal gauge is 0.65 mm. Exbolt 63 and Exbolt 68 are separate models, not alternative names for this string.
What is Elasticity Outer?
Yonex describes a flexible nylon coating using NANOALLOY technology. Increased shuttle hold is a manufacturer claim; the specification does not provide a universal dwell-time or control measurement.
Is Exbolt 65 the same as BG66 Ultimax?
No. Both are 0.65 mm, but Exbolt 65 specifies a Forged Fiber outer and Elasticity Outer coating, while Ultimax lists a braided nylon outer. Compare actual response rather than diameter alone.
Does Exbolt 63 use the same coating?
The global Exbolt 63 specification does not list Elasticity Outer. Do not copy Exbolt 65's coating claim to the thinner 63 model.
Does the coating make Exbolt 65 soft or rough?
It does not establish a universal finished feel or a measured surface-friction value. Your racket, installation and contact affect the sensation. Compare soft returns and full shots under familiar conditions.
What tension should I request for Exbolt 65?
Use your racket's permitted range, frame condition, previous setup and intended change as the starting information. There is no single recommended number for every Exbolt 65 user.
Should I automatically pre-stretch it?
No. Discuss pre-stretch and main-and-cross settings as part of the specific racket, string and machine procedure. A coating name does not prescribe a universal percentage.
How many sessions will Exbolt 65 last?
No fixed session count is established here. Wear, contact, tension and equipment condition vary. Record playing hours and useful response as well as the eventual break.
Where is the Exbolt 65 DT loss graph?
No verified model-specific ERR time series was found in the checked material. This page provides a measurement checklist instead of reusing another string's graph or inventing values.
When should I consider Exbolt 68 instead?
When you want to compare a thicker 0.68 mm option with a stronger durability emphasis. You still need to assess touch and usable response; the thicker string is not automatically better for every player.
What is the listed ERR Exbolt 65 restringing price?
The ERR list checked on 15 November 2026 shows RM51 including string and labour. Confirm the current price, colour and availability through the existing appointment or enquiry process.
What should I include in my Exbolt 65 booking enquiry?
Include your racket model, existing string, previous tension, playing frequency and one response you want to change. Confirm the Setapak appointment before travelling.
How did Yonex Exbolt 65 play for you?
Your experience can help another player choose their next string.
What players say
Your first-hand experience matters.
Be the first to review Yonex Exbolt 65. Share what you liked and what could be better.
Ready to discuss your string setup?
Bring your Exbolt 65 questions, racket model and previous setup. Discuss the contact feel you want before choosing the next restring.
Book stringing Explore the string listBook stringing.
Bring your racket and questions.
Discuss your Exbolt 65 setup with ERR before visiting. Tell us your racket model, previous tension and the shot or feel you want to review.
Book through ERR MemberAsk ERR on WhatsApp ↗Prepare a question for your visit
Open WhatsApp with my question ↗You can review your message in WhatsApp before sending.The ERR string list checked on 15 November 2026 lists Exbolt 65 at RM51 including string and labour. Confirm the current price, colour and availability before your visit. The catalogue entry is not proof that every colour is in stock, and Japanese retail pricing does not set the local restringing charge.
Send your racket model, current string, previous tension, playing frequency and preferred response through the existing ERR Member booking process or the Exbolt 65 WhatsApp enquiry. Add one practical concern, such as soft returns travelling too far or clear length becoming inconsistent. That gives the discussion a starting point.
ERR is in Taman Melati Utama, Setapak, Kuala Lumpur. Players travelling from Wangsa Maju or elsewhere in KL can use the map and confirm their slot before setting off. After the restring, keep a short record of familiar shots and playing hours so any follow-up adjustment has a clear reason.
By appointment · Check available slots before travelling.
Find us in Taman Melati Utama
G-3, PV6 Platinum Hill Condo, No. 3 Jalan Melati 3, Taman Melati Utama, 53100 Kuala Lumpur, Malaysia.
Get directions in Google Maps ↗


